Everlast Hurricane 220 MTS-C MIG, AC/DC Pulse TIG, Stick & Plasma Welder

The Everlast Hurricane 220 MTS-C is a true four-in-one workshop machine: MIG, AC/DC pulse TIG, DC stick and plasma cutting in one compact, portable unit. Change the torch, press a button, and you're on the next process. It runs on a standard New Zealand 230V single-phase supply and comes fitted with a 15A plug.

Features

• MIG, AC/DC pulse TIG, DC stick and 40A plasma in one machine
• Power-Set synergic setup in every process, with full manual override
• HF and lift-start TIG in both AC and DC
• AC TIG for aluminium with square, soft-square and triangular waveforms
• Pulse TIG, up/down slope and adjustable pre/post flow
• MIG for steel, stainless and aluminium, with adjustable burn-back and inductance (MIG Wave)
• Spool gun ready for aluminium MIG (spool gun optional)
• Adjustable stick arc force and hot start
• 2T/4T trigger latch for MIG and TIG
• 16 program memories
• Blowback pilot-arc plasma with low-air safety
• Takes a 200mm (8") wire spool. Light enough for one person to carry

Ideal for

Home and farm workshops, automotive and exhaust work, field repair, fabrication, prototyping and metal art.

Specifications (230V NZ supply)

• Type: Digital IGBT inverter
• Input: 230V single phase, 50Hz
• Plug: NZ 15A plug fitted
• Input current: 16A effective / 31A max
• Open circuit voltage: 64V (MIG/TIG/stick), 250V (plasma)
• MIG: 20–225A, 225A @ 35% duty cycle
• TIG: DC 10–225A, AC 20–225A, 225A @ 35% duty cycle
• Stick: 10–180A, 180A @ 60% duty cycle
• Plasma: 20–40A, 40A @ 60% duty cycle
• Duty cycles rated at 40°C
• TIG pulse: 0.5–150Hz
• Up/down slope: 0–5 s. Pre-flow 0–5 s, post-flow 0–10 s
• Wire: 0.8–0.9mm standard, up to 1.2mm with optional rolls. Flux core optional
• Max wire feed speed: approx. 15 m/min
• Spool: up to 200mm (8") diameter, approx. 5kg
• Stick electrodes: 1.6–3.2mm

Welding and cutting capacity (230V)

• MIG steel/stainless: 10mm single pass, 16mm multi-pass, down to 0.6mm sheet
• MIG aluminium: 8mm single pass, 10mm multi-pass, down to 1.6mm
• TIG steel: 8mm single pass, 12–16mm multi-pass
• TIG aluminium: 6mm single pass, 10mm multi-pass
• Plasma: 12mm everyday cutting, 16mm severance, 8mm max pierce
• Plasma air: 4.5–5 bar, clean dry air

What's in the box

• SN-24 MIG gun, 3m, Euro connector
• 26 series air-cooled TIG torch, 3.8m, 35 Dinse
• MTS torch switch, 3.8m, 7-pin plug
• Foot pedal, 7.6m cable, 7-pin plug
• IPT-40 plasma torch, 4.3m, Euro central connector
• Earth clamp, 1.8m, 35 Dinse
• Stick electrode holder, 3m, 35 Dinse
• Argon regulator
• Air filter / water trap
• 0.9–1.2mm V-groove drive roll (fitted)
• Starter plasma and TIG consumable kits (tungsten not included)

Good to know

• Not intended for CNC plasma use
• On a generator, use clean power only (8.5kW+ surge, 5% THD or less)
• E6010 rods can be run but may struggle with long arc lengths

Backed by the Everlast warranty. See our Everlast Warranty page for NZ terms.